All about product
Self-impression locksmith key for opening door lock cylinders AGB Scudo DCK (Italy).
It is recommended to use self-adhesive foil with a thickness of 0.03 mm or 0.04 mm.
Text in the 1st video: Hello. This is the AGB Scudo DCK. The key has an interactive element. The tool also has an interactive element. This is an example of how to stick foil. It must be pasted evenly, this is very important. Here I use self-adhesive foil 04. We stick the foil in such a way that it GOES a little on this element, but does not cover it. Approximately so. Insert carefully so as not to wrinkle the foil. And little by little we swing. Check the key. Let's try the next one. Insert the handle right away. The handle is not to apply force, it is for convenience. It is very convenient to swing, so it is included. Of course, you can load a little force, but not much, since this is not a power key. Insert carefully. The foil may tear, as happened now. If this happens, then re-stick the foil. I have prepared in advance. Insert carefully. It tears. A little torn, but let`s try anyway. We check the key. This is how you can open these locks. The kit includes a handle, tool and foil. You will find the price on our website, the link is under this video. Bye
Text in the 2nd video: In this video we will show cutting foil for AGB Scudo DCK. Recommended foil 04. Cut out the strip. From the emphasis. Here is the emphasis. From the stop to the beginning of the wheel. Like this, so that it covers the wheel a little. Similarly here, from the stop to this place. Cut out this strip. Now, how is it more convenient to stick? We need a plastic card, for example, and a knife, a sharp knife. Now put the foil like this. We press and it sticks. We leave a little gap. We turn over. Make a light tention and wrap. Now lay down and take a knife. Wait a minute, I'll put that away so it doesn't get in the way. So, I take a knife.Here is the line. I'm running this line. Now I take a plastic card and carefully, not close to this part, but a little further, swipe it. And we look very carefully so that the working part, here it is the working part, remains even. We turn over. Similarly - I put a knife and swipe the surface, now a plastic card. Well, pay attention, here is such a small wrinkle. We can leave it, but ideally there should be no such jams. So let's do it this way. Now align, on top, like this. Now we pass the corners. I think this is already clear to many, but I show it all the same in advance so as not to answer unnecessary questions later. Smooth out the surface: corners, top line, corner, this part. And we go through the central milling. Here's what we got. This is how everything should be smooth. This small jam is, in principle, acceptable, but it’s better not to do this. If it is very wrinkled, it is better to tear off and re-stick, because the lock may not open because of this. Everything should be even. Now let's open some lock. Why, by the way, is it important not to wrinkle the foil? Here, in front, is a high secret, very high. And here it is, too, very high. If at this point we wrinkle the foil, the lock will not open. We take the handle. Fix. Insert very carefully. And slowly swing. Force is not required. Well, just a little. So, in this way you should stick the foil. The price of the tool will be on the website, the link is under this video.
Text in the last video: This is AGB DCK. Key with elements. And this is the tool. We use self-adhesive foil 03. The main foil is 03. If suddenly you can’t open the lock, then try using 04. Glue the foil evenly, tightly. We insert it very carefully so that the foil does not tear. Make not strong, but sharp jerks. And then we gradually increase the amplitude and gradually increase the force. But we do more jerk movements than power ones.
