All about product
An impression type lockpicking master key for opening cylinder locks such as BASI BM, Titan I6, TITAN K56.
It is recommended to use cut foil with a thickness of 0.05 or 0.06 mm.
Do not apply force!!!
Text in the video: Hello. There are three models of cylinders. Three types here. This is BASI BM, two rows of pins, but the top one is not active. BASI BM. And two Titans. These are TITAN I6 and TITAN K56. In general, we have TITAN K56, TITAN I6 and BASI BM. One tool is used for these three types of cylinders. The working foil is placed only on the main row. You don’t need to put anything on the top row. Either 0.5 or 0.6. I didn’t see much of a difference. Plus or minus is the same. Either 0.5 or 0.6. And about these locks, they have very mushroom-shaped pins. And they are very difficult to open. But it can open. Let’s say there is one here, it opens by itself. I shook the top one, from right to left. Now we’ll try the same. And it opened by itself. But this is rare. Most often, one of the pins does not press through. As a rule, it is one. And you have to try to find this one and push it through. It's like a system. Well, at least try. Because it doesn't often open by itself. You'll have to try to find a pin that doesn't sag. And push the foil through that place. I'll try to explain it all quickly and clearly now. Let's start with the one that can open itself in principle. This is BM. It just has a lighter key pattern, so it can open itself. Well, if you're lucky. The top row is inactive. On the back side, we make sure to make a shape. Oh, by the way, for the tool. The profile is quite thin. It must be used carefully. The key itself is not thick, the tool is not powerful. And you need to pump it carefully with an appropriate load. We transfer it to the working part. Carefully insert it. Make sure it doesn't get dented. Carefully, with such light movements. Well, it starts normally. As usual, tension on the left side and up and down. Sometimes you can make quick, but not strong movements, just quick ones. Like this: quickly-quickly-quickly in different directions. You can try this too. Well, and I repeat, as it happened now, this is an easy option, it doesn’t happen often. Another Basi BM. The drawing is more complicated here. I’ll try 0.5 foil. There’s no point in pumping the tool for a very long time. Pump 10-20 times. And after that, you can try to find and try to press through some pin that didn’t press through itself. To press through the pin, you need to pull it out very carefully so that the foil retains its shape, it stays on the key. Because if you pull it out, the foil will fly apart. You need to be careful. As a rule, this works. Here, if you compare it with the key, it didn’t press through anymore. You can still try. This one was pressed through, and this one. Here we see high ones in the middle. As a rule, some of the high ones aren’t pressed through. You can just choose at random. Not all the way through, but about the middle. You can choose a little below the middle. In general, this is not an easy task. I don’t think this will work anymore. Now I'll try to open another one. Let's take Titan I-6. The pattern is also quite complex. There was a click, a stronger backlash appeared. In principle, after this you can try. Compare with the key. First, second. Here, the whole pattern is assembled, except for one. Let's try to show it close-up, if possible. Here it is, the top one. One of the high ones. Here we have one high and the second high. Either one or the other must be pressed. Let's say you pressed this one, but it did not open. Then we reload the foil and work again. And the next time we do not touch this one, but press this one. Here it is. As a rule, at this level. We press somewhere in the middle and try. This often happens when one pin is approximately high, well, it stands high, it needs to be pressed further. So, it will not be easy with these locks. There will be no 100% opening. But the tool was made. Once again about the tool. It is thin, the profile. Therefore, swing, apply force very carefully. It can be broken, bent. That is, in addition to the complexity of the locks themselves, the instrument itself, well, it is not super strong, so work with it very carefully. Well, but it fits three. Three types of bass and two titanium.
