All about product
Impression type (with foil0 locksmith tool for KALE 6 pins is made of high-quality steel.
Includes sliced foil. Recommended foil is foil with thickness 0.6 mm.
Foil trowel, handle and hex wrench.
Text in the 1st video: These are the Spanish cylinder FAC and the Turkish Kale, which are essentially the same thing, absolutely the same profile, so the tool is also the same. We use foil 06. And we start with one strip, and if that doesn’t work, then we put two strips. Or you can use tougher foil. So, let's start with one strip. The main thing is that the height of the foil is not pressed down, that is, we try not to wrinkle it. Well, with one strip it quickly opened, but it also quickly jamms a little. Now let's try to put two strips. We put one on top of the other. You can right away put it on the working part. Smooth it out a little with a ruler. So, with two strips, the process is more stable. Now Turkish Kale. We start with one strip. Good with one stripe. Here is Kale with side pins, that is, with pick protection. Let's try with one strip. Well, there’s a little bit of a bite there, but it went quickly. So, with two stripes the opening process will be more stable.
Text in the 2 nd video: This is a single row Kale lock, 6 pins. Such a key. Such a turning knob in the back. These are very old models. After them, with the same profile, there is already such a turning knob. These 2 locks have been bought today, completely new, in such boxes. The lockpicking tool for them is the same. By the way, there is a slight difference in size between the old and new locks. In old ones it can easily slip, and in new ones it can fit tightly. But it fits both the old and the new. We mainly use 06 cut foil. In some cases, you can use 07, only in some. Here are 5 locks, here is another one in a vice. Of these five locks, 4 were opened. Rather, this one that did not open, it opened on the fifth attempt once using sheet foil 07, but the next attempts to open it again failed. Therefore, if the lock did not open, it makes sense to try to open it again and again, it may work. It happens that the lock enters anti-peaking, a large backlash appears, this is how it is, and when such a backlash appears it means that the lock will no longer open, there is no longer any point in pressing it. In some cases, when the lock does not open when pressed lightly, it makes sense to do it sharply and hard, and then there is a possibility that it will open. Regarding all other locks, all of them open using 06 foil, successfully and quickly. I'll take two new ones. Sometimes it spins for a long time, sometimes it wedges. Pay attention, when we lay down the foil, do not press the height of the foil with our fingers. They put the foil down, rubbed your fingernail over it lightly and that's it. Make sure that this does not happen. We take the next one. That is, sometimes it happens very quickly, sometimes slowly. But 90% of the locks in this series are opened with this pick and foil 06. I press hard enough. Now there is anti-picking. Here I entered the lock, a backlash appeared and this means that it will no longer open. On the other side there is a profile, you can also put it on this side, shape it and then transfer it to the working side. I try to press a little weaker. 5 seconds. Now it wedges a little. Well, this can be said already opening, two turns. So just like that, with these locks, one can get caught that will not open. And you can also try foil with a different thickness.
Text in the 3rd Youtube video: This is a single row Turkish Kale, 6 pins lock. Today we’ll talk about how to properly use foil for this lock and not only for this to raise the percentage of opening to maximum. Basically, 06 cut foil is used, in one layer. That's enough. In rare cases, double-layer foil can be used, or 07 foil can be used in sheets. But usually only one strip is always enough, if everything is done correctly. In general, we lay down a strip and bend the nose a little. The foil can be a little smoothed by such a ruler. When inserting, it is desirable to look down here, so that it can be seen that the foil does not wrinkle or tear. Here is. And here, in these locks and many others, for example, with a two-row Kale, in general, where the instrument is made for a certain lock, it is important to press well and sharply. That is, not in the same way as with an impression tool of similar type for Chinese budget locks, with such light movements. If you work like this, then the probability of opening decreases. You need to load well. But without fanaticism, of course. Good and sharp. That is, we press in one direction, and sharply in the other. That is, without this... With this method of operation, the percentage of opening increases greatly. A link to our website will be at the end of the video.
