All about product
Kit for emergency opening of lever tumbler locks such as SECUREMME 4+4, KALE, MOTTURA, Mul-T-Lock, FUARO, BARRERA, etc.
Text in the 1st video: Securemme 4+4, with such keys and such a set for opening: two handles, an impression magic key, a cutter and a hook. The cutter is inserted and rotated in any direction, you can do this by swinging. Next, the impression tool is inserted. It may fit a little tight. You can push it a little. And we work until we fall into the false groove. When we feel that we are approaching, we insert the hook from the side of the crossbars, from this side. We hold the tool tight and look for the clamped lever by the mark. Here it is. It is important not to confuse it. Backlash. Here it is crampled from the other side. We lower it by about 2 mm and look further. And I remind you that in this lock, we only need to open this first turn. All the other three turns have the same pattern, only the right and left will change.
Text in the 2nd video: Hello. This is Securemme 4x4 and a set for opening. A cutter with a handle, an impression with two handles, right and left, a hook-manipulator and a pin. First, insert the cutter and turn it left or right, it doesn't matter. After that, you can insert the impression. The handle must first be calibrated so that the extreme marks... this extreme one and this extreme one, coincide with the hook, with the first and last pin. The lock has false grooves, it gets into these false ones and with the help of this mark and the hook we simply feel and lower each pin. The lever that we were looking for by feeling, it is clamped, accordingly we lower the pin by 2 mm. Even if we do not hear a click, nevertheless, the lock very quickly gets into the anti-picking, it can smoothly go there, there will not necessarily be a click. We hold the tool taut and feel it. These locks are very readable, so we feel it and look for the one that is squeezed. Here it is, squeezed. 2 mm, approximately 2 mm. We press 2-3 times and feel it again. The last one is squeezed, we lower it, approximately 2 mm. We press several times and feel it again. Here it is, the third one, squeezed, we lower it, approximately 2 mm. The lock is open. After opening the first turn, the remaining 3 can be left unopened. The pattern will match, you just need to change it. Right-left, right-left, mirror. So, here is such a kit. It is made specifically for Securemme 4x4, but this tool matches many locks. These are Securemme 4x4, and Matura 4x4, and Kale 4x4, and Fuaro 4x4, and Mul-t-lock 4x4, and something else. In total, there are about 6 locks that this impression matches in size and opens them successfully. But the set was originally made specifically for Securemme, because there are difficulties in bypassing false grooves.
Text in the 3rd video: This is Securemme 4 + 4. These are the keys and the opening kit. Now I will try to show everything. So that everything is clear. The kit includes a cutter with a handle for cutting the inner guide. Then comes the impression itself. Right and left handle. And a hook. This is the kit. So, we install the lock. The lock is mirrored. That is, it is not necessary to open all sides. It is enough to open the first side. All other turns can be simply duplicated. First of all, the cutter. We insert it left or right, it does not matter, swing it, you can scroll it, and thus cut off the guides. After this, the tool can go in. Handle with markings. We need to calibrate a little, put the hook at the level of the first pin. First pin. And the mark should correspond to the first notch. The latter pin with the latter mark. And the first pin with this latter mark. It is better to tighten with pliers. This will make it easy to feel for the false grooves. Because the lock has false grooves. Well, let's start working. The first time after the cutter, the tool may go in a little tightly, but there are no problems with this. Let's start working. Insert the hook. Hold the tool taut. And feel for the levers that are clamped. Here, the last one is clamped. The one that is clamped needs to be lowered by 2 mm. A couple of clicks and we look for the next one. They are very easy to feel. Here it is, clamped. We lower it by about 2 mm in the same way. We insert it again and look for the clamped one. It is very clearly visible here by the mark. Here, now the third one. Such a click means that we have entered a trap again, a false groove. The third one from the end. Another trap. The fourth one. Now the first one. ....Already a little bit lost. If lost, you can fix it, each height a little bit higher. This is the imprint, the first one, the second one will be the same - mirrored, and so on. You don't need to open it any further. You need to assemble the same thing. Just right-left. This is the set. Once again. What's included? Two handles (right and left), a hook, a manipulator, an impression and a cutter with a handle.
