All about product
Power impression locksmith tool for opening cylinder locks such as: Picard VTX, DOM T250, TITAN T200 & T250 (France, Germany, Slovenia).
It is recommended to use cut foil with a thickness of 0.06mm.
Text in the 1st video: This is Titan, model T-200, T-250. Now we will try T-200. Basically, there is no difference. T-200 does not have side pins, T-250 does. That's the only difference, but otherwise it is the same. Power impression, foil 0.6. WD is desirable, very desirable. Yes, and without foil it does not fit. If anyone does not know, it can fit a little, very badly, it does not fit. Therefore, it is inserted together with foil. Then it fits normally. We make a form, we make a good form, this is important. On the back side, and then, as usual, we move it to the working part. We insert it so that the foil does not wrinkle, carefully. And the impression does not fit all the way at once. A few, 2-3 millimeters. It needs to be pushed in a little. We press forward a little and start to rock it a little. And it fits like that. Tightly-tightly and fits in. Press well. And start rocking. Gradually, no force is needed right away. Just start gradually-gradually and rock. Press a little all the time inward. A little jammed, at half a turnTry rocking it further. It went quite easily. And, most likely, the lock will remain intact. Trying to get it out. Yes, the lock remained intact. This is not always the case. Sometimes it gets damaged, the guides get damaged. Here it doesn't even jam. Absolutely intact lock. Impression fits French Picard models, for VTX DOM. DOM, similarly. Titan series T200 and T250. Here are 4 models.
Text in the 2nd video: This is Picard. France. This is what the cylinder and key look like. There are many wave options and that’s why the instrument has been made as force tool, with a universal wave. And so we will try to rotate it by force by rocking it. We use foil 06 and lubricant. We make the shape on the reverse side. There are deep grooves here, so you can use a plastic card. Transfer to the working part. The last couple of millimeters the tool fits in very tightly, so you will need to push it in a little. Accordingly, we use a power handle, because we will need to apply a load. First of all, we push it inward and when we start swinging, we will also push it inward, so that it goes all the way. Slowly at first and gradually increase the strength. Here, came right in. Crunches. That`s good. It is better not to use too much force right away, because you can break the tool and the lock will not open. It's better to rock it more. It is better to spend more time, but there will be a greater chance that the lock will open. And don’t forget to constantly press it inward. You may not be able to see it, but I do this all the time because it gets thrown out of there a little. Well, overall, it has been opened relatively easily. The key most likely no longer works. We can try to check it out. It is functioning. But it goes hard. This kit comes with a handle like this.
Text in the 3rd video: Titan T-250. DOM. This is a DOM lock. It says Metalux series here. But it's DOM. Picard is French. In general, DOM, Titan, Picard, they're all the same. The same locks. Now let's try to open the DOM. The side pins are the main ones and the sliders. We will open the wave by force, so the tool is a little forceful. And the handle. We make a shape on the back side. Only after that we transfer it to the working part. And just as we will apply a little force, it is advisable to use a WD or similar lubricant. Well, it will work better this way. And carefully insert it so that the foil does not tear. The tool must go in tightly, so it goes all the way. And when we swing it, we also press forward a little. First, slowly, slowly and then harder and harder. No need to rush. First, apply a little force. Because too much force can break it. It needs to be swinged gradually. It jammed a little in this position, but with such sharp movements we continue to tear it off. It was DOM-Metalux.
